Asphalt shingle blow-off – how does it happen? And what can you do about it?

If you have an asphalt shingle roof, having the shingles blow off in the wind is one of the ways it can fail.  This post explores what this failure looks like, the possible consequences, some of the causes, and how to ensure this doesn’t happen to you.

Shingle blow-off happens with both new and old roofs.  The more common failures happen near the rakes/gables and below the ridge-line.  There are several causes, some relating to the quality of the installation, and some to the quality of the product.

New roof, shingle blow-off

New roof, shingle blow-off
(Click on image to see it full size)

This image shows a recently installed roof (about 2 years old), which already experienced shingle-blow-off.  While the shingles themselves were installed with a certain degree of care in terms of placement, the nailing pattern shows that the installer did not follow the standard practice, and nailed them too high, which shows either that they didn’t care, or were in a hurry and did place the nails in the right places.  In addition, this particular roof is getting winds directly from the lake without any protection, and the roofers did not attempt to increase the wind resistance of the roof by using any of the techniques for high-wind installation.

Shingle Blowoff_MG_8894_v2

New roof with shingle blow-off
(Click on image to see it full size)

This is a new roof, installed in the fall.  In the spring, the roof is already showing wind damage.  It appears that the fall installation resulted in the tar strips not sealing, and although the roof “looks” well installed, it will continue to fail.  To quote the warranty from one shingle manufacturer (BP) ( ):

“For the Warranty against wind blow-off to take effect, the self-seal adhesive must be subjected to sufficient heat to activate the bond. When the shingles are installed in environmental conditions that will not produce such temperature or in very windy areas, the shingles should be sealed down with spots of asphalt plastic cement as specified in CSA A123.51-M85.  In addition, contamination of the self-sealing adhesive by dust or foreign matter may prevent the sealing strip from achieving  a full thermal seal. Prior to sealing, shingles are more vulnerable to wind damage.”

 The concern about proper sealing of the tar strip is also seen in the warranty language of IKO (another shingle manufacturer): (

(i) the Limited Wind Resistance Warranty will only apply if: (a) the Shingles were installed using roofing nails (not staples) in strict accordance with the instructions on the wrapper and (b) for installations in Canada during the fall, winter or in cool weather, the Shingles have been manually sealed at the time of installation, and for installations at all other times in Canada, and at all times in the U.S., the Shingles have been manually sealed at the time of installation, or have had the opportunity to seal down;

 In short, if the installation of the shingles takes place late in the season, then the roofer needs to take extra precautions to ensure that the shingles do NOT lift prior to the roof having enough heat to melt the tar strips, and therefore effect the seal.


Shingle blow-off despite attempt at “sealing”
(Click on image to see it full size)

 In the above example, the roofer obviously considered the possibility of blow-off and dabbed each shingle with some roofing cement.  However, they did not follow the recommended practice, and the roof still ended up with shingle loss. 


Workmanship as a contributing factor to shingle blow-off
(Click on image to see it full size)

 This example shows the effect of poor workmanship.  The nailing pattern is too high, the shingle alignment is poor, the flashing work is certainly lacking, and there any many signs of a hurried installation.  It can be seen that some repairs were attempted. 


Shingle blow-off due to loss of shingle flexibility.
(Click on image to see it full size)

As the asphalt shingles age, they become more brittle.  In some products, there is also shrinkage of the felt and some clawing or curling.  In the above case, the shingles did, for the most part, stay flat, but as can be seen on a number of shingles, started to crack horizontally.  If the tar strip is only partly sealed, then this provides very little resistance to wind forces, with the result that the shingles are susceptible to blow off.


Shingle blow-off can lead to deck damage.
(Click on image to see it full size)

In the above example, we can see that the wind blow-off exposed the deck.  This is another example of the roofer apparently cutting corners by not installing any kind of underlayment under the shingles.  If the wind was strong enough to break off the shingles, it is also strong enough to blow rainwater in between the shingles and onto the roofing deck.  If the roofing deck is not protected by underlayment, then this will result in persistent wetting of the deck.  Depending on the type of decking, this persistent wetting may cause delamination of the plywood, or complete loss of structural integrity in OSB, or contribute to rotting of wood.

Decking with no underlayment_IMG_0062_v2

Deck damage due to lack of working underlayment.
(Click on image to see it full size)

This image from inside an attic, shows what happens when there is no underlayment (or poorly installed underlayment).  Water has been seeping into the deck, causing:

  • Delamination of the plywood (as can be seen by the cracking of the wood veneer),
  • Rusting of nails (every nail is rusty)
  • Entry of water into the attic interior, which increased humidity in the attic and supports growth of mold (see the dark marks on both the underside of the wood, and in the insulation,
  • Loss of decking integrity (as can be seen at the movement of the wood at the H-clips).
Damaged Decking_MG_5446_v2

Deck damage due to missing underlayment.
(Click on image to see it full size)

In the above case, the plywood decking lost enough integrity to require complete redecking.  Fortunately, the mold inside the attic was minimal (due to decent ventilation that ended up drying the moisture as it seeped in), so additional measures of removing the insulation were NOT needed.  The cause of the problem was the failure of the roofer to install appropriate underlayment, and to take into account the slope of the roof and the way the roof system worked.

 How do you avoid this kind of damage?

There are two solutions:

  1. Choose installers who take the time to do it right, who are aware of the weaknesses of each type of material they work with, and who provide the proper second (and third) line(s) of defense in anticipation of strong weather events.
  2. Choose products and installation methods that have a proven track record of preventing the kinds of damage seen in these photos.

Elsewhere on this blog (in the articles section), I’ve posted an article on how to get a good quote for your roof.  What is relevant to this section is the degree of care the prospective roofer pays to understanding your actual situation, and to ensure that the resulting quotation addresses all of the needs.  It should be clear that in most of the above cases, work was done in a hurried manner, without consideration of how failure could occur, and without providing for adequate countermeasures to these modes of failure.

The most effective way to avoid having to worry about blow-off, is to use products and installation methods that CAN withstand wind damage, and associated issues such as damage by wind-driven rain.  These products and installation techniques are more expensive than what one would pay for conventional asphalt shingles, but they look expensive only when ignoring the true durability and the true cost of repairing damage caused by poor choices.

If you are tired of worrying whether your roof will protect your home from the next wind storm, give me a call to explore the options that you need to consider.

(c) 2014 Paul Grizenko

Update (January, 2017):  This article has had thousands of views.  If you have some specific questions on any aspect of the discussion above, please use the comment form (next to the post title) to post the question or comment.  All comments are moderated, and will appear after review and approval.


13 thoughts on “Asphalt shingle blow-off – how does it happen? And what can you do about it?

  1. Very informative particularly since I’m presently in a dispute with my builder over shingle loss in each of 6 years in a 7 year old house. He refuses to own any responsibility because it’s outside of his warranty period. My position is that product and/or application are at issue. From your article installation may very well be the cause. The shingles were applied in January without being manually sealed and possibly with improper nailing as well. Not having expertise makes it difficult for me to be certain.



    • Hi Ed,

      There are several things you will need to check on. First, what does Manitoba have in terms of consumer protection, and how does it apply to this situation? Since I am not familiar with Manitoba’s legislation, I cannot give you any advice with respect to the protections that you may be entitled to under the law (as far as the roofer’s warranty period is concerned). Secondly, each shingle manufacturer has specific instructions on how their product needs to be installed, and these instructions are (usually) downloadable from the manufacturer’s website. This should allow you to identify if the shingle application conformed to the manufacturer’s guidelines. Third, depending on the manufacturer, some installation issues may be covered under the manufacturer’s warranty, but this usually requires you to have proof of purchase of the product from the manufacturer in question. If the roofer was subcontracted by the builder of your home, then it is your builder’s responsibility to ensure that the installation was properly done. To my knowledge, most new homes are required to have a warranty from the builder of 10 years (at least that is the situation in Quebec – Manitoba may be different). Unfortunately, many builders will find the cheapest subcontractor and the cheapest subcontractor isn’t cheap because he does everything exactly right.

      Note as well that your roof slope, deck preparation, and roof configuration can all have an effect on the performance of the shingles. Hopefully you have some photos taken during the installation that should allow you to see whether the proper installation practice was used.

      Kind regards,



  2. Paul: I have a 19 year old Hateras roof in Mississauga installed by Sharp exteriors. The shingles are 40 year. My old roof never lost a shingle despite the builder being disreputable. This roof was installed in in the winter of 1999 and after about 10 years started losing a few shingles in the spring, about 5 times. Repairs were done but in a windstorm today, we lost about 15 shingles. Our neighbours are fine and I suspect that they paid less than we did. I suspect faulty installation. What do you recommend?


    • A winter installation of asphalt shingles will almost always result in a poor seal of the tar strips on the shingles. As the shingles age, they tend to shrink a little, and this shrinkage will break the weak sealing bonds. In general, I prefer not to install asphalt shingles during the time of the year when there’s not enough heat from the sun to make these tar strips melt and bond. In my area that would be anytime between end of October to end of April. I don’t know the reasons why the roof was installed in winter, but the reputable roofers I know will not carry out such an installation when they know the shingles won’t properly seal.

      If you look up Certainteed’s warranty on the Hatteras shingle, it is clearly stated (pg. 4) that shingles installed in fall or winter may not seal until the following spring. Even that is not the full truth, as during that period wind can blow fine dust between the shingles, effectively making sure that the seal will never happen.

      Another factor to consider is that the “40-years” you refer to is the length of the limited manufacturer’s warranty, which is in my opinion a marketing document. It is unusual to find shingles (no matter how long the warranty is for) that last beyond 20 years. In actual practice, many of the roofs we end up replacing are no more than 12-15 years old. While Certainteed is a very good brand, when we install the so-called “lifetime” shingles, we warn the homeowners that a realistic expectation should be in the 15-20 year range. Without examining your roof and the shingles I can’t venture an opinion if the shingles are finished or not, but it would be my recommendation to consider replacing them.


      • Thanks Paul, your comments are most useful. All along, I considered that the installation was inferior, but having paid a lot, I never doubted the 40 year claim and expected to never have to replace the roof. Now I just have to accept that the roof has to be redone.


      • You’re not the first person from Ontario asking about their roof. I strongly suggest you review the sections in the blog talking about how to get a quote (although I focus on my local market, Montreal, the principles remain the same), and what else you need to know on top of asking for the three quotes. I have also done long-distance consulting with the customers sending me pictures of their roof, attic, etc., and copies of the quotes they received. I believe in the end my consulting clients got much better results than they would have had on their own. There is obviously a consulting charge for that, and you will have to decide if it is worth it to you.

        There are two posts that are referenced when you select “Quotes” from the subject section. They in turn will lead you to other relevant sections.


  3. On the back of each shingle is a thin clear strip along one edge – should this be peeled off prior to installation or left in place – I have been told both remove and do not remove


  4. Very enlightening article.

    We suffered wind damage last year and lost several shingles, By the time I was able to get someone to fix it, we had water intrusion and cold weather (December in southern Ontario).

    Six weeks later, a portion of the patched area suffered shingle loss again. The original roofer came and replaced the missing shingles but told my wife, they were going to keep blowing off as the whole roof needs replacement.

    Sure enough, two days later and I can see the shingles flapping in the wind (no loss yet fortunately).

    From what I could see, there was no underlay at all, just bare plywood.

    Is there something we could do in the meantime to hold the shingles on until we can replace the whole roof?

    And does replacing the whole roof mean the plywood underneath as well?


    • The latest article in this blog refers to why you want to have “two” roofs, not one. If you can see the plywood (no underlay), then it is possible that this roof is the first (original) roof on the house, as our building codes DO allow no underlayment if it’s new construction. If the roof is a re-roof, then the last roofer was cutting too many corners. Since you mentioned “the original roofer”, it appears that this is the first roof. You may want to ask him why no underlayment was used. Furthermore, it is not clear from your post as to how old the roof is. If it is only a few years old, then you may have a warranty claim. If it’s 10 years (or later), then it may be reaching the end of its life (we see many shingles with so-called 30-year warranties require replacement after 10 years).

      In situations such as yours, I would conduct an inspection of the plywood from the inside of the attic. The nails holding the shingles to the deck should be protruding through the plywood by at least 1/2″. If the nails are rusty, and the wood around the nails is discoloured, then this is telling you that the roof is no longer working, and the water is entering by the nailholes. Furthermore, in the areas under the shingle blow-off, you need to see if there is any water staining visible. If so, there’s no question that the roof needs to be replaced as soon as possible.

      Replacing the whole roof does NOT mean replacing the plywood underneath, unless it has rotted or delaminated. However, upon stripping the roof, a very careful inspection should be done to see whether the deck is still solid enough to support new shingles (and the dead weight of winter snow).


  5. Hi, I have a prefab home that was built in the ealy summer and placed on the foundation in late July of 2016. We are about 500 feet from the ocean in Cape Dauphin, NS. I have not had any shingle loss yet. What can I do to ensure I don’t lose shingles in a wind sotrm? I presume some type of tar under the shingles? What is the best practice for applying the tar?


    • Asphalt shingles depend on the tar strip (located on the underside of each shingle) bonding (under the heat of the sun) the shingle to the one below. As shingles age, they can become more brittle and the expansion and contraction (day to night, warm seasons to cold seasons) can create stresses in the shingles that will cause them to crack. Since the shingles are tarred along the leading edge, a crack behind the tar strip can allow the wind to get under the shingle above the tar strip, and tear it. Sometimes, the failure is due to the tar strips themselves drying out and cracking. As a homeowner, you should keep an eye on how well the shingles stay flat and bonded. If the outer edges of the shingles start to lift, some roofing cement on the underside “may” help, but if the shingle is already brittle, then bending it back to place the roofing cement may break it. Therefore, if you see the shingles becoming brittle and cracking, you may be looking at a roof replacement.

      The best protection against water infiltration after shingle blow-off, is a good waterproofing membrane under the shingles, installed during the shingle installation. If you do not have that installed, you have to keep a very close eye on the health of the shingles. In our experience, the shingles can last as little as 10 years, and as long as 30 years. The warranties are marketing documents, not promises of shingle durability.


Leave a Reply to michele Cancel reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s