Most people assume that the visible external roof covering is the “real” roof, which functions to keep the water and weather out of the roof system. This is true for flat or low-slope roofing materials, but not true for steep-slope materials (which is anything over a 3:12 roof slope). Steep-slope materials are designed to shed water. That means that water is supposed to run off the surface, and if properly layered, the water stays on the outside. However, if wind or a physical obstruction interrupts the water flow, then it will go under the roofing material. This is true for all steep-slope roofing material, whether it is made of asphalt shingles, or metal shingles, or metal panels, or cedar shakes, or slate.
It’s the unappreciated and unloved underlayment layer that’s below the top layer that has the job of actually keeping the water out. That layer is the “true” waterproof roof, which is composed of layering of flashings, membrane, underlayment, and sealants. It’s also the layer which is easiest to skimp on when the contractor is being pressed to come up with a low price. If you can’t see it, and you don’t even know that it needs to be there, then why would you want to pay for it?
How does the saying go? Ah yes. Penny-wise, pound foolish.
That is a curious result that happens. Someone finally invests some serious money in upgrading their kitchen (or bathroom), installing beautiful cabinetry, gorgeous ceiling lights, and finally get the attractive and bright kitchen (or comfortable bathroom) that they always wanted. The following winter, an ice dam forms. The following year, the ice dam gets worse and the ceiling starts to leak after every thaw. What’s going on?
Roof stripping, that is. This is the process of getting rid of the old roof covering material, down to the deck. In the process, if done correctly, you’ll learn a lot of things about what worked on your roof and what didn’t. As all things that are good for you, there are costs and inconveniences involved, aspects which are exploited by those contractors who don’t have your best interests at heart.
What are some of the typical reasons you’re given why leaving your old roof on and going over is/are acceptable? They include:
You’re saving money.
It’s more ecological (no landfill waste!).
It’s more secure.
It provides another layer of protection to your roof.
It’s recommended by the manufacturer.
There’s much less residual mess to clean up.
So many great reasons why you should just leave the old roof on, and go over! And yet, pretty much all of these are false, based on the homeowner’s lack of knowledge of how the roof system is supposed to work, and compounded by the contractor’s desire to get the job done as fast as possible, get paid, and move on. If you are presented with the suggestion that leaving your old roof on is an acceptable strategy, there are a number of things you should be aware of before you agree to this.
Closed cell-spray foam used as insulation, has been on the market since about 1979, and has gone through a number of evolutionary steps. The product is a solid plastic, formed by the chemical reaction of two primary components: an “A” side which is isocyanate, and a “B” side which is usually a mixture of oils, stabilizers, fire retardants, blowing agents, and colouring agents. The reaction is exothermic (ie, generates a lot of heat), and the materials form a solid within seconds. The blowing agents are the compounds which produce the low-conductivity gas that forms the bubbles in the foam, and thereby form the primary insulation.
When applied to a minimum thickness of 50mm (slightly under 2 inches), the material acts as insulation, vapour barrier, and an air barrier. Newly-installed foam has R-values of R-6 to R-7.5 per inch, but this diminishes to about R-5 per inch over time as the insulating gas dissipates. Compared to other insulation products like fiberglass bat or mineral wool bats, the product has more insulating value per inch, and resists the loss of heating value that sometimes occurs with loose insulation due to air convection with extreme temperature differences.
The ability to prevent air and vapor movement is generally a good thing, except in situations where moisture can enter a wood structure, and then cannot get out. Therefore the short answer to the question in the header is “spray foam is good when PROPERLY installed, and BAD when installed in inappropriate places or in an incorrect manner. There are also issues of the impact on the environment, and potential impact on the health of the people living in the homes where the product is used. The rest of the post touches on some aspects that inform whether the installation is good or not.
During the month of January, I’ve been called to diagnose roof leaks on an almost daily basis. These leaks have a common characteristic – they show up when it’s cold. That usually signals that there is some form of accumulation of water on the roof, usually behind an ice dam, and that the waterproofing is insufficient to stop the water from forcing its way it. The existence of an ice-dam almost always means that there is excessive transfer of heat to the roof which melts the snow on the upper sections, and the resulting meltwater refreezes on the lower section over the soffits. To reduce this heat transfer, we rely on insulation (to reduce the amount of heat leaking into the attic) and ventilation (to dissipate the residual heat before it melts the snow on the roof). However, there is another player in this game, and it can cancel out the efforts at insulating and ventilating. That player is air leakage.
When you look up various web sites advocating consumer help or protection, you often get the advice to ask for three quotes. The idea is that by getting these quotes, you are protecting yourself from contractors that are going to overcharge you, or from contractors who are undercharging because they are unqualified. This is excellent advice, but it usually doesn’t go far enough. As always, the really important stuff is in the details (the fine print). Let’s examine the issues.
Frost can be beautiful. One of the benefits of poorly insulated windows, at least for small children, is the beautiful lace shapes that form – so delicate and yet so enchanting.
Despite this beauty, there are plenty of places where in a home you do NOT want to see frost forming. Certainly, when found on windows, it is a clear sign that the window is not very good at insulating. Another place where you don’t want to see frost, is inside your attic.
Thermography is the use of thermal infrared energy emitted by various surfaces to create an image using a camera sensitive to thermal infrared photons. Depending on the camera, sensitivity and resolution, it shows the relative temperature of that surface. Since surfaces differ in the way they radiate thermal energy, it does require some understanding of physics, underlying structure, and device operation to meaningfully extract the information contained in a thermographic image.
Most people think they have a good grasp of how roofs work – the shingles (usually asphalt) keep the water out, and that they do that by being the waterproof layer that stops water from getting in. That’s more myth than fact.
Another myth, is that caulking is an acceptable way to achieve waterproofing.
Another myth, is that if you have ice-and-water shield on your roof, you’re good.
What all these myths have in common is that they misunderstand how a sloped roof system works in reality.